It just came to my attention that computer architecture is transitioning from the PCI interface to the PCI Express interface.

This supports my contention that Firewire (IEEE 1394) and USB 2.0 are the preferred methods for connecting high-quality, high-resolution audio interfaces to computers.

While I have two RME Multifaces (the original, not the Multiface IIs shown in the link) that use dedicated PCI cards, this means that if I purchase a new computer with a PCI Express interface, I’ll have to purchase two new PCI Express interface cards for the RME Multifaces — and hope that RME makes it at the time I need it. Many users have expressed satisfaction with their Digital Audio Labs CardDeluxe.

This sounds a lot like the Zefiro Acoustics ZA-2 ISA card that is languishing in a Dell Dimension XPS PII 333 MHz machine.

My recent foray into an audio interface via IEEE 1394 was the MOTU 828 MK II. So far, I am happy and it’s finding uses in the studio as well as the remote notebook-centric applications I originally acquired it for.

I would think that a good audio interface might last longer than a good PC, so consider this approach.

Many pieces of equipment with cross-headed screws actually have Pozidriv screws rather than Phillips screws in them. This is especially true of Japanese equipment. [EDIT 2007-11-26] Or are these yet different JIS screws? See the updated post about this here.

I bought a set of Hozan [JIS] drivers, but now that I’ve learned that PB makes them [maybe] (see tools article) I’ll buy any additional ones from them. Pozidrive screws have “tick” marks between the slots–or should.

Here is an interesting explanation of the different screw heads in the context of cabinet/furniture making.

After some testing with both Phillips and Pozidrive drivers, it seems that some/many of the inexpensive screws that come packaged with home hardware-type items are non-descript and perhaps don’t meet either standard!

One way of loading C-0 cassettes is to unscrew the shell and drop the old tape into the new shell.

I have found that reloading using a modified cassette machine is much faster and easier. The following images should explain the process:

Splice one end of the original tape into the C-0:

(more…)

We have been wondering just how far we can push the Sony APR-5000 capstan servo system, so we ran a few tests using an external oscillator feeding the reference port. Unlike Ampex, Otari, and Studer machines which use an external reference of 9,600 Hz; the Sony machines use an external reference of 19,200 Hz.

We found that the APR-5000s did not run reliably below 1.88 in/s — and that is achievable with a -50% varispeed already. It didn’t matter what the base speed was.

The APR-16 (cousin of the APR-24) did not run reliably below 3.75 in/s. But the good news was that we could bring 15 in/s down to 3.75 in/s using the external reference source. We were also able to run the APR-16 at 60 in/s, but takeup tension was a bit low.

The 108 memory locations for storing setups is a real feature of the APR-5000 series tape machines. The APR-24 manual alluded to this but did not provide any instructions.

I have the only APR-16 that Sony ever made, but it is essentially the same as an APR-24. My APR-16 is running firmware version 5.01.06.0.

It appears that there are a total of 18 total preset locations in the APR-16 (and presumably the APR-24). (more…)

The 2 mm hex head screws that hold panel modules and blanks on Studer A810s are easily stripped by slightly worn hex drivers. Studer used 2.5 mm hex head screws in the later A807, perhaps aware of this issue. Using PB drivers from the start will reduce the possiblity of this happening.

There are essentially two choices when this happens:

• Slot the screw with a Dremel rotary tool and a small cutoff blade and use a slotted screwdriver to remove the screw.
• Use some sort of Ez-Out screw extractor.

When I was confronted with this situation recently and I didn’t have an EZ-out of the correct size to bite into the screw without drilling, I grabbed a T10 Torx driver and gently tapped it into the screw head. I pushed in hard while starting to turn and the screw came out.

High-quality hand tools are a must for working on high-end tape machines. I’ll discuss some of the specifics in other articles.

The tools that Studer supplied (when required) were made by PB Baumann in Switzerland.

My preferred supplier (for North America) is Tool Lady. She also sells Wiha tools to complement the PB line.

I have made a variety of static pages for my tape restoration Web site, but thought it was time to add a more user-friendly, article-based location to discuss various topics, tools, tricks, and techniques that I have come across in various ways.

What is easier to use than ready-made BLOG software, so I guess Richard is finally Blogging!

I hope you like this and find it of interest. Please let me know of any changes or topics you might like addressed.

Enjoy!

Note: This post has been put in every top-level category because it appears that a post is needed in each top-level category if the sub-categories are to be visible.

Note 2: The Tips & Notes blog and the Formats & Resources static pages of this sub-site replace the Tips and Resources static pages on the Web site. And, there is integrated searching across both the blog articles and the static pages.