I received a cassette from a client and he complained that the previous recording was audible as well as the new recording.

There are several ways this can happen:

• The erase head can be dirty—this usually leads to high frequencies being erased and lower frequencies still audible
• The erase head can be misaligned—this often provides a partial erasure, but careful use of track selection can find a section of track with less crosstalk.
• A similar problem occurred on quarter-track reels with misaligned record heads where recordings from the opposite direction would invade the tracks for the forward directions. Again, a specially adjustable narrow head usually solves this.
• A completely non-functioning erase system—this is what we suspect happened with the current project. There were no track dissimilarities nor any other way we could find, including looking at the tape with the 8-track cassette recorder to separate the underlying, unwanted recording from the wanted one.
• A totally unrelated mechanism that may sound the same is if the microphone or tape recorder picks up a broadcast or other radiated signal and records that along with the desired signal.

We opted not to proceed with any noise gating as it would not improve the overall audio quality for listening and may actually impede transcrption.

While not a success, we were able to confirm to the client that there was no way that could preserve the fidelity of the desired sound and remove the undesired sound. The desired interview was completely intelligible and could be transcribed. It was just distracting to listen to.

“Noise Reduction” is a potentially confusing topic, partially because it has come to be used to mean two different things.

1. Today, it means removing noise from a recording by means of a single-ended post-production device or plug-in, such as Noise Free Pro by Algorithmix that I use (among other tools).
2. Historically, the term was used for a double-ended process where the dynamic range of the program material was reduced in an unobtrusive way, transported by the noisy channel (be it tape or broadcast) and then expanded in a complementary fashion at the end/output of the noisy channel. These devices were generally referred to as companders (a contraction of compressor/expander).

When reviewing old tapes, they may be marked in various ways to indicate their noise reduction compression, or processing. As of this writing, there are no software plug-ins that accurately mimic the action of the hardware compander acting as an expander. We use actual companders from the original systems when restoring tapes made with these systems.

We currently handle nine different formats from four manufacturers and are always on the lookout for more. Most manufacturers sold a variety of systems tailored to the needs of different kinds of transmission/recording channels

See our special page under formats (click here) to see some of the information we’ve gathered about noise reduction techniques used over the years. Check back as we uncover additional formats and information.

You’ve been asked to digitize recordings in your collection and don’t have any idea where to start. There are several resources on this site which might be of use. 

What I use is shown on my facility page. That’s one of the main reasons it is there. If I’m using it, it’s because I like it or it solves a problem for me. If I’m not using it, either I don’t have an opinion about it, won’t spring for it, or don’t like it. (more…)

I received a phone call today from someone who wanted my opinion on a Tascam 238 8-track cassette recorder for recording his music.

This was like the person who wanted to know about the DCC recorder for the same purpose yesterday.

People keep hearing that “analog sounds great” or that this or that format “sounds great” and they want to buy in. (more…)

Many pieces of equipment with cross-headed screws actually have Pozidriv screws rather than Phillips screws in them. This is especially true of Japanese equipment. [EDIT 2007-11-26] Or are these yet different JIS screws? See the updated post about this here.

I bought a set of Hozan [JIS] drivers, but now that I’ve learned that PB makes them [maybe] (see tools article) I’ll buy any additional ones from them. Pozidrive screws have “tick” marks between the slots–or should.

Here is an interesting explanation of the different screw heads in the context of cabinet/furniture making.

After some testing with both Phillips and Pozidrive drivers, it seems that some/many of the inexpensive screws that come packaged with home hardware-type items are non-descript and perhaps don’t meet either standard!

One way of loading C-0 cassettes is to unscrew the shell and drop the old tape into the new shell.

I have found that reloading using a modified cassette machine is much faster and easier. The following images should explain the process:

Splice one end of the original tape into the C-0:

(more…)